脱氧铝切块机,铝棒切块机,铝杆切断机

联系我们

济南陆勤机械有限公司

联系人:张经理

电 话: 0531-83831136

电 话:18654536782

地址:山东省济南市章丘相公庄工业园

切断机生产厂家共享钢筋切断机操作规程

浏览量:   来源:www.xaedsh.cn  作者:陆勤

圆钢切断机厂家分享钢筋切断机安全操作规程:


幸运飞艇冠军一期7码Round steel cutting machine manufacturers share the safety operation rules of steel cutting machine:




一、切断机四周应有足够的钢筋堆放场地。


1. There should be enough reinforcing steel yard around the cutter.




二、转动的部件应有防护罩。


2. The rotating parts should have protective cover.




幸运飞艇冠军一期7码三、须检查刀片有无裂纹,刀片固定螺丝是否紧固。


3。 It is necessary to check whether the blade is cracked and whether the fixing screw of the blade is tightened。




四、不准用两手分别握住钢筋的两端剪切,只准用手握住靠身边一端的钢筋上。


4. Do not hold the two ends of the reinforcing bar with two hands separately, only hold the reinforcing bar on the side with one hand.




五、工作时用双手握住钢筋,对准刀口,待上刀片下来觉得压手时,立即用力压住钢筋,防止尾端翘起伤人。


Fifth, when working, hold the steel bar with both hands and aim at the edge of the knife。 When the knife blade comes down and feels pressure on the hand, press the steel bar vigorously immediately to prevent the tail end from warping up and hurting people。




幸运飞艇冠军一期7码六、 禁止切断直径超过机械规定的钢筋和烧红的钢筋,多根钢筋同时切断时,必须换算钢筋的截面,及时调整刀片,以防止意外。


6。 It is forbidden to cut reinforcing bars with diameters exceeding the mechanical requirements and red-burning reinforcing bars。 When multiple reinforcing bars are cut at the same time, the section of reinforcing bars must be converted and the blades adjusted in time to prevent accidents。




幸运飞艇冠军一期7码七、切断低合金钢筋时,应换高硬度刀片。


7. When cutting low alloy steel bar, high hardness blade should be replaced.




幸运飞艇冠军一期7码八、切断短料时,手握一端的长度不得小于40cm,靠近刀片手与刀片的距离,应保持在15cm以上。


8. When cutting short material, the length of one end of the hand should not be less than 40 cm, and the distance between the hand and the blade should be kept above 15 cm.




九、切断较长钢筋时,应有专人帮扶钢筋,帮扶人与操作人动作一致,并听其指挥不得任意拖拉。


9. When cutting long reinforcing bars, special people should help reinforcing bars, help people and operators to act in accordance, and listen to their command can not be arbitrary procrastination.




十、机械运转中严禁用手清理刀口附近的杂物,现场禁止闲杂人员逗留。


10. It is strictly forbidden to clean up the debris near the edge of the knife by hand during the operation of the machine. It is forbidden for idle and miscellaneous personnel to stay at the scene.




十一、发现刀片歪斜异常现象,应立即断电检修。


11. Discovering abnormal deflection of blade, the power should be cut off and repaired immediately.http://www.xaedsh.cn


天天幸运飞艇计划软件手机版 幸运飞艇杀一码公式 幸运飞艇杀一码公式 幸运飞艇2码选号技巧 幸运飞艇5码计划软件 幸运飞艇如何看走势图 幸運飛艇 幸运飞艇计划网页2期 幸运飞艇如何看走势图 幸运飞艇6码两期技巧